soundqert.blogg.se - Rockford fosgate punch amp

#ROCKFORD FOSGATE PUNCH AMP HOW TO#
#ROCKFORD FOSGATE PUNCH AMP FULL#

Crossovers - Your amplifier may utilize an internal crossover.

However if, for some reason, you need to manually reset them, use the method above described in Stereo Mode. These usually do not need adjustment from the factory.

Gain Control - The input gains for left and right channels need to be set to the same level when operating in Mono (Bridged) Mode.

If your source unit or signal processor only provides one (1) sub-level pre-out, use a "Y-adapter" to convert the (1) RCA feed into (2) RCA inputs. When using the RCA inputs, both inputs must be utilized. Use only one method when connecting an input signal to the amplifier. Low-Level inputs are used when the source unit has preamp line (RCA) outputs. Hi-Level inputs are used when the source unit only has speaker line outputs.

Signal Input - Your amplifier may have either Hi-Level or Low-Level inputs.

#ROCKFORD FOSGATE PUNCH AMP HOW TO#

Mono (Bridged) Mode - The diagram below illustrates how to configure most Rockford Fosgate 2-channel amplifiers for mono mode. It is important that you do not connect a speaker system to your amplifier that results in an impedance lower than the minimum recommended for your amplifier. Speaker Impedance - most Rockford Fosgate amplifiers can operate at 2-Ohms or 4-Ohms per channel.

#ROCKFORD FOSGATE PUNCH AMP FULL#

If so, the crossover can be set to High-Pass (HP) for use with midrange speakers & coaxials Low-Pass (LP) for use with subwoofers or Full Range (FULL) for use with component systems. 3) Slowly increase both L/R gain controls until the system is at its maximum listening level. 1) Turn the amp's gain controls to minimum. If they have been re-adjusted for some reason, you can manually rest them by using the following procedure: With the system turned on.

Gain Control - The input gains for left and right channels operate independently, however these usually do not need adjustment from the factory.Stereo Mode - The diagram below illustrates how to configure most Rockford Fosgate 2-channel amplifiers for stereo mode. For specific setup and wiring configurations, please refer to your owner's manual. Dimensions (HxWxL): 2.38 x 7.76 x 9.86 (in) / 6.05 x 19.71 x 25.N O T I C E This answer illustrates the importance of proper signal input, gain setting, crossover configuration & speaker impedance with any Rockford Fosgate amplifier.Average Current Draw (13.8V Music): 23 A.Visual Indicators: Power/Protect/Thermal LED.Remote Controls: Optional Punch Level Control (PLC2) Ready.Speaker Output Connector: Captive C-Clamp.Function depends upon LP/AP/HP switch position.Punch EQ2 Treble: 0dB to +12.5dB 12kHz.Tone Controls: Punch EQ2 Bass: 0dB to +18dB 45Hz and/or.Low-Pass: 50Hz-250Hz 12dB/octave Butterworth.Crossover Controls: High-Pass: 50Hz-250Hz 12dB/octave Butterworth.Frequency Response: 20Hz to 20kHz +/- 1.0dB.Dynamic Power (PVC/PowerCube® Measurement):.Total Power (Sum of Rated Power): 300 Watts.

On-board Punch EQ with +18dB boost 45Hz.Optional remote Punch Level Control (PLC2) ready (w/ input clip indicator).High level input capable with Auto Turn-On circuit.Regardless if you're driving multiple speakers or just one, the hefty 2-ohm capability will deliver the right amount of PUNCH that you want! Now, thanks to its small chassis design, it will also fit where traditional amplifiers cannot. The P300X1 is perfect for use as a dedicated subwoofer or center channel amplifier.